Pembicaraan:Wikipedia: Perbedaan antara revisi
Konten dihapus Konten ditambahkan
→Teknik dan Konfigurasi Jaringan VLAN: bagian baru |
→Teknik dan Konfigurasi Jaringan VLAN: bagian baru |
||
Baris 1.456:
Selamat anda baru saja menjalani langkah demi langkah bagaimana melakukan setting pada
Network VLAN. hanya itu saja. Mudah Bukan ???
== Teknik dan Konfigurasi Jaringan VLAN ==
; Teknik dan Konfigurasi Jaringan VLAN
Kali ini saya mendokumentasikan tentang bagaimana mengkonfigurasi jaringan VLAN pada
network switching layer 2. Di sini saya menggunakan cisco simulator 4, meski pun kita tidak
mengakses perangkat switch secara real, konfigurasi simulator ini cukup canggih dan sangat
membantu, sayang nya ada beberapa perintah yang tidak support pada simulator tersebut, seperti
menjalankan spaning tree. Terus terang saja konfigurasi jaringan pada Network VLAN cukup
sederhana, tetapi pemahaman mendasar tentang konsep bagaimana network switching layer 2
bekerja sangat membantu anda. Ada beberapa hal yang saya ingin anda ketahui disini, agar dapat
membantu anda dalam memahami dunia networking VLAN, pastikan anda memahami konsepkonsep
dasar yang dibawah ini :
- konsep dasar TCP/IP, Broadcast domain, collision domain
- konsep dasar bagaimana switching layer 2 bekerja
- konsep dasar Spanning Tree
- konsep dasar VLAN
- Konsep dasar Trunking
- konsep VTP (Virtual Trunking Protokol)
- bagaiman VTP Server dan VTP Clien bekerja
- konsep enkapsulation ISL dan dot1Q
- Tentu saja bagaiman cara Routing antar VLAN
- Setting dasar sebuah VLAN seperti hostname, password, dan ip address
Hanya itu saja yang diperlukan untuk memahami dunia VLAN, ketika anda memahami semua
konsep dasar diatas maka sebesar apapun network VLAN yang anda bangun tidak akan menjadi
masalah, untuk tingkat pemula dan setting VLAN standart tentunya. Di sini saya tidak membahas
tentang semua konsep-konsep diatas karena untuk membahas itu semua memerlukan ruangan
tersendiri. Untuk memahami semua konsep diatas anda bisa googling di internet, OK
Baik mari kita mulai membangun jaringan VLAN pertama kita. Pada skenario kita kali ini, VLAN
yang kita bangun terdiri dari :
- 6 buah Cisco Switch 2950 dan 1 Buah Cisco Router
- 15 Host yang masing-masing Switch terkoneksi dengan 3 host
Berikut Data lengkap Alokasi IP address dari Network VLAN yang kita bangun
Switch
name Hostname
Vlan
Members IP addres
Subnet
Mask Gateway
Switch A A_2950 VLAN 1 172.16.10.3 255.255.255.0 172.16.10.1
Host_A VLAN 2 192.168.20.2 255.255.255.0 192.168.20.1
Host_B VLAN 4 192.168.40.3 255.255.255.0 192.168.40.1
Host_C VLAN 3 192.168.30.3 255.255.255.0 192.168.30.1
Switch B B_2950 VLAN 1 172.16.10.4 255.255.255.0 172.16.10.1
Host_D VLAN 2 192.168.20.4 255.255.255.0 192.168.20.1
Host_E VLAN 5 192.168.50.3 255.255.255.0 192.168.50.1
Host_F VLAN 3 192.168.30.4 255.255.255.0 192.168.30.1
Switch C C_2950 VLAN 1 172.16.10.5 255.255.255.0 172.16.10.1
Host_G VLAN 4 192.168.40.4 255.255.255.0 192.168.40.1
Host_H VLAN 2 192.168.20.5 255.255.255.0 192.168.20.1
Host_I VLAN 5 192.168.50.4 255.255.255.0 192.168.50.1
Switch D D_2950 VLAN 1 172.16.10.6 255.255.255.0 172.16.10.1
Host_J VLAN 3 192.168.30.5 255.255.255.0 192.168.30.1
Host_K VLAN 4 192.168.40.5 255.255.255.0 192.168.40.1
Host_L VLAN 2 192.168.20.6 255.255.255.0 192.168.20.1
Switch E E_2950 VLAN 1 172.16.10.7 255.255.255.0 172.16.10.1
Host_M VLAN 5 192.168.50.5 255.255.255.0 192.168.50.1
Host_N VLAN 3 192.168.30.6 255.255.255.0 192.168.30.1
Host_O VLAN 4 192.168.40.6 255.255.255.0 192.168.40.1
Main Switch Main_Switch VLAN 1 172.16.10.2 255.255.255.0 172.16.10.1
Router
Sub
interface VLAN Gateway IP address Subnet mask
0 / 0.1 VLAN_Switch 172.16.10.1 255.255.255.0
0 / 0.2 VLAN 2 192.168.20.1 255.255.255.0
0 / 0.3 VLAN 3 192.168.30.1 255.255.255.0
0 / 0.4 VLAN 4 192.168.40.1 255.255.255.0
0 / 0.5 VLAN 5 192.168.50.1 255.255.255.0
VLAN Members VLAN ID Network
Marketing VLAN 2 192.168.20.0
Finance VLAN 3 192.168.30.0
Support VLAN 4 192.168.40.0
Operation VLAN 5 192.168.50.0
Langkah-langkah yang dilakukan dalam membangun jaringan VLAN ini adalah :
1. Design Network VLAN yang anda bangun
- Buat design network, nama group VLAN dan Alokasi Subnet IP addres pada tiap VLAN
1. Konfigurasi Router-VLAN
- Setting Hostname
- Setting Password
- Setting Subinterface
- Setting encapsulation dotlq x
- Setting ip address untuk segmentasi VLAN
2. konfigurasi MainSwitch
pada main switch yang dikofigurasi adalah
- Setting HostName
- Setting Password
- Setting IP address VLAN
- Setting Trunking pada port yang terkoneksi dengan perangkat lain
- Setting VTP Server
- Setting VTP Domain
- Setting VTP Database
- Setting nomor dan nama-nama VLAN
3. Konfigurasi Switch yang bergabung dalam VLAN
- Setting Hostname
- Setting Password
- Setting IP Address VLAN
- Setting Trunking pada port yang terkoneksi dengan perangkat lain
- Setting VTP Client
- Setting VTP Domain
- Setting Port untuk didaftarkan pada suatu VLAN
4. Verifikasi koneksi dan VLAN membership
- Melihat pada switch port mana yang sudah di daftarkan ke VLAN
- Melihat VLAN membership dari setiap switch
- Cek Koneksi dengan ping ke setiap segment network dari berbagai tempat
Sebenarnya konfigurasi VLAN cukup sederhana anda hanya mengikuti konfigurasi seperti dibawah
ini. tapi sekali lagi pemahaman mendasar tentang konsep yang berhubungan dengan VLAN seperti
trunking, protokol ISL atau IEE 802.1Q (dot1q) cukup membantu dalam trobleshooting ke depan
Mari kita mulai konfigurasi Network VLAN kita :
Gambar Topologi VLAN yang akan dibangun
Router VLAN Configuration
Router Con0 is now available
Press RETURN to get started!
Router>enable
% Incomplete command.
Router#configure terminal
% Incomplete command.
Router(config)#hostname Route_VLAN
Route_VLAN(config)#enable secret fery
Route_VLAN(config)#line console 0
Route_VLAN(config-line)#password fery
Route_VLAN(config-line)#login
Route_VLAN(config-line)#exit
Route_VLAN(config)#line vty 0 4
Route_VLAN(config-line)#password fery
Route_VLAN(config-line)#login
Route_VLAN(config-line)#exit
Route_VLAN(config)#service password-encryption
Route_VLAN(config)#interface fastethernet 0/0
Route_VLAN(config-if)#no ip address
Route_VLAN(config-if)#no shutdown
03:37:51 %LINK-3-UPDOWN: Interface Fastethernet0/0, changed state to up
03:37:51 %LINEPROTO-5-UPDOWN: Line protocol on Interface Fastethernet0/0, changed state
to up
Route_VLAN(config-if)#exit
Route_VLAN(config)#interface fastethernet 0/0.1
Route_VLAN(config-subif)#encapsulation dot1Q 1
Route_VLAN(config-subif)#ip address 172.16.10.1 255.255.255.0
Route_VLAN(config-subif)#exit
Route_VLAN(config)#interface fastethernet 0/0.2
Route_VLAN(config-subif)#encapsulation dot1Q 2
Route_VLAN(config-subif)#ip address 192.168.20.1 255.255.255.0
Route_VLAN(config-subif)#exit
Route_VLAN(config)#interface fastethernet 0/0.3
Route_VLAN(config-subif)#encapsulation dot1Q 3
Route_VLAN(config-subif)#ip address 192.168.30.1 255.255.255.0
Route_VLAN(config-subif)#exit
Route_VLAN(config)#interface fastethernet 0/0.4
Route_VLAN(config-subif)#encapsulation dot1Q 4
Route_VLAN(config-subif)#ip address 192.168.40.1 255.255.255.0
Route_VLAN(config-subif)#exit
Route_VLAN(config)#interface fastethernet 0/0.5
Route_VLAN(config-subif)#encapsulation dot1Q 5
Route_VLAN(config-subif)#ip address 192.168.50.1 255.255.255.0
Route_VLAN(config-subif)# --->CTRL+Z
Route_VLAN#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
Route_VLAN#
2950 Main Switch Configuration
switch Con0 is now available
Press RETURN to get started!
switch>enable
% Incomplete command.
switch#configure terminal
% Incomplete command.
switch(config)#hostname 2950-MainSwitch
2950-MainSwitch(config)#enable secret fery
2950-MainSwitch(config)#line console 0
2950-MainSwitch(config-line)#password fery
2950-MainSwitch(config-line)#login
2950-MainSwitch(config-line)#exit
2950-MainSwitch(config)#line vty 0 15
2950-MainSwitch(config-line)#password fery
2950-MainSwitch(config-line)#login
2950-MainSwitch(config-line)#exit
2950-MainSwitch(config)#service password-encryption
2950-MainSwitch(config)#interface fastethernet 0/6
2950-MainSwitch(config-if)#switchport mode trunk
2950-MainSwitch(config-if)#description Trunking to Router-VLAN
2950-MainSwitch(config-if)#exit
2950-MainSwitch(config)#interface fastethernet 0/1
2950-MainSwitch(config-if)#switchport mode trunk
2950-MainSwitch(config-if)#description Trunking to A_2950
2950-MainSwitch(config-if)#exit
2950-MainSwitch(config)#interface fastethernet 0/2
2950-MainSwitch(config-if)#switchport mode trunk
2950-MainSwitch(config-if)#description Trunking to B_2950
2950-MainSwitch(config-if)#exit
2950-MainSwitch(config)#interface fastethernet 0/3
2950-MainSwitch(config-if)#switchport mode trunk
2950-MainSwitch(config-if)#description Trunking to C_2950
2950-MainSwitch(config-if)#exit
2950-MainSwitch(config)#interface fastethernet 0/11
2950-MainSwitch(config-if)#switchport mode trunk
2950-MainSwitch(config-if)#description Trunking to D_2950
2950-MainSwitch(config-if)#exit
2950-MainSwitch(config)#interface fastethernet 0/12
2950-MainSwitch(config-if)#switchport mode trunk
2950-MainSwitch(config-if)#description Trunking to E_2950
2950-MainSwitch(config-if)#exit
2950-MainSwitch(config)#interface VLAN 1
2950-MainSwitch(config-if)#ip address 172.16.10.2 255.255.255.0
2950-MainSwitch(config-if)#no shutdown
2950-MainSwitch(config-if)#exit
2950-MainSwitch(config)#ip default-gateway 172.16.10.1
2950-MainSwitch(config)#vtp mode server
Device mode already VTP SERVER.
2950-MainSwitch(config)#vtp domain jetcoms
Changing VTP domain name from NULL to jetcoms
2950-MainSwitch(config)#exit
2950-MainSwitch#VLAN database
2950-MainSwitch(VLAN)#VLAN 2 name Marketing
VLAN 2 added:
Name: Marketing
2950-MainSwitch(VLAN)#VLAN 3 name Finance
VLAN 3 added:
Name: Finance
2950-MainSwitch(VLAN)#VLAN 4 name Support
VLAN 4 added:
Name: Support
2950-MainSwitch(VLAN)#VLAN 5 name Operation
VLAN 5 added:
Name: Operation
2950-MainSwitch(VLAN)#apply
2950-MainSwitch(VLAN)#exit
APPLY completed.
Exiting....
2950-MainSwitch#show VLAN
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
2 Marketing active
3 Finance active
4 Support active
5 Operation active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
2950-MainSwitch#
Switch A_2950 Configuration
switch Con0 is now available
Press RETURN to get started!
switch>enable
% Incomplete command.
switch#configure terminal
% Incomplete command.
switch(config)#hostname A_2950
A_2950(config)#enable secret fery
A_2950(config)#line console 0
A_2950(config-line)#password fery
A_2950(config-line)#exit
A_2950(config)#line vty 0 15
A_2950(config-line)#password fery
A_2950(config-line)#exit
A_2950(config)#service password-encryption
A_2950(config)#interface VLAN 1
A_2950(config-if)#ip address 172.16.10.3 255.255.255.0
A_2950(config-if)#no shutdown
A_2950(config-if)#exit
A_2950(config)#ip default-gateway 172.16.10.1
A_2950(config)#interface fastethernet 0/1
A_2950(config-if)#description Trunking toMainSwitch_2950
A_2950(config-if)#exit
A_2950(config)#interface fastethernet 0/5
A_2950(config-if)#switchport access VLAN 2
A_2950(config-if)#exit
A_2950(config)#interface fastethernet 0/6
A_2950(config-if)#switchport access VLAN 4
A_2950(config-if)#exit
A_2950(config)#interface fastethernet 0/7
A_2950(config-if)#switchport access VLAN 3
A_2950(config)#vtp mode client
Aetting device to VTP CLIENT mode.
A_2950(config)#vtp domain jetcoms
Changing VTP domain name from NULL to jetcoms
A_2950(config)#apply
A_2950(config)#exit
F_2950#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
A_2950#
Switch B_2950 Configuration
switch Con0 is now available
Press RETURN to get started!
switch>enable
% Incomplete command.
switch#configure terminal
% Incomplete command.
switch(config)#hostname B_2950
B_2950(config)#enable secret fery
B_2950(config)#line console 0
B_2950(config-line)#password fery
B_2950(config-line)#exit
B_2950(config)#line vty 0 15
B_2950(config-line)#password fery
B_2950(config-line)#exit
B_2950(config)#service password-encryption
B_2950(config)#interface VLAN 1
B_2950(config-if)#ip address 172.16.10.4 255.255.255.0
B_2950(config-if)#no shutdown
B_2950(config-if)#exit
B_2950(config)#ip default-gateway 172.16.10.1
B_2950(config)#interface fastethernet 0/1
B_2950(config-if)#description Trunking toMainSwitch_2950
B_2950(config-if)#exit
B_2950(config)#interface fastethernet 0/5
B_2950(config-if)#switchport access VLAN 2
B_2950(config-if)#exit
B_2950(config)#interface fastethernet 0/6
B_2950(config-if)#switchport access VLAN 5
B_2950(config-if)#exit
B_2950(config)#interface fastethernet 0/7
B_2950(config-if)#switchport access VLAN 3
B_2950(config)#vtp mode client
Aetting device to VTP CLIENT mode.
B_2950(config)#vtp domain jetcoms
Changing VTP domain name from NULL to jetcoms
B_2950(config)#apply
B_2950(config)#exit
B_2950#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
B_2950#
Switch C_2950 Configuration
switch Con0 is now available
Press RETURN to get started!
switch>enable
% Incomplete command.
switch#configure terminal
% Incomplete command.
switch(config)#hostname C_2950
C_2950(config)#enable secret fery
C_2950(config)#line console 0
C_2950(config-line)#password fery
C_2950(config-line)#exit
C_2950(config)#line vty 0 15
C_2950(config-line)#password fery
C_2950(config-line)#exit
C_2950(config)#service password-encryption
C_2950(config)#interface VLAN 1
C_2950(config-if)#ip address 172.16.10.5 255.255.255.0
C_2950(config-if)#no shutdown
C_2950(config-if)#exit
C_2950(config)#ip default-gateway 172.16.10.1
C_2950(config)#interface fastethernet 0/1
C_2950(config-if)#description Trunking toMainSwitch_2950
C_2950(config-if)#exit
C_2950(config)#interface fastethernet 0/5
C_2950(config-if)#switchport access VLAN 4
C_2950(config-if)#exit
C_2950(config)#interface fastethernet 0/6
C_2950(config-if)#switchport access VLAN 2
C_2950(config-if)#exit
C_2950(config)#interface fastethernet 0/7
C_2950(config-if)#switchport access VLAN 5
C_2950(config)#vtp mode client
Aetting device to VTP CLIENT mode.
C_2950(config)#vtp domain jetcoms
Changing VTP domain name from NULL to jetcoms
C_2950(config)#apply
C_2950(config)#exit
C_2950#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
C_2950#
Switch D_2950 Configuration
switch Con0 is now available
Press RETURN to get started!
switch>enable
% Incomplete command.
switch#configure terminal
% Incomplete command.
switch(config)#hostname D_2950
D_2950(config)#enable secret fery
D_2950(config)#line console 0
D_2950(config-line)#password fery
D_2950(config-line)#exit
D_2950(config)#line vty 0 15
D_2950(config-line)#password fery
D_2950(config-line)#exit
D_2950(config)#service password-encryption
D_2950(config)#interface VLAN 1
D_2950(config-if)#ip address 172.16.10.6 255.255.255.0
D_2950(config-if)#no shutdown
D_2950(config-if)#exit
D_2950(config)#ip default-gateway 172.16.10.1
D_2950(config)#interface fastethernet 0/1
D_2950(config-if)#description Trunking toMainSwitch_2950
D_2950(config-if)#exit
D_2950(config)#interface fastethernet 0/5
D_2950(config-if)#switchport access VLAN 3
D_2950(config-if)#exit
D_2950(config)#interface fastethernet 0/6
D_2950(config-if)#switchport access VLAN 4
D_2950(config-if)#exit
D_2950(config)#interface fastethernet 0/7
D_2950(config-if)#switchport access VLAN 2
D_2950(config)#vtp mode client
Aetting device to VTP CLIENT mode.
D_2950(config)#vtp domain jetcoms
Changing VTP domain name from NULL to jetcoms
D_2950(config)#apply
D_2950(config)#exit
D_2950#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
D_2950#
Switch E_2950 Configuration
switch Con0 is now available
Press RETURN to get started!
switch>enable
% Incomplete command.
switch#configure terminal
% Incomplete command.
switch(config)#hostname E_2950
E_2950(config)#enable secret fery
E_2950(config)#line console 0
E_2950(config-line)#password fery
E_2950(config-line)#exit
E_2950(config)#line vty 0 15
E_2950(config-line)#password fery
E_2950(config-line)#exit
E_2950(config)#service password-encryption
E_2950(config)#interface VLAN 1
E_2950(config-if)#ip address 172.16.10.7 255.255.255.0
E_2950(config-if)#no shutdown
E_2950(config-if)#exit
E_2950(config)#ip default-gateway 172.16.10.1
E_2950(config)#interface fastethernet 0/1
E_2950(config-if)#description Trunking to MainSwitch_2950
E_2950(config-if)#exit
E_2950(config)#interface fastethernet 0/5
E_2950(config-if)#switchport access VLAN 5
E_2950(config-if)#exit
E_2950(config)#interface fastethernet 0/6
E_2950(config-if)#switchport access VLAN 3
E_2950(config-if)#exit
E_2950(config)#interface fastethernet 0/7
E_2950(config-if)#switchport access VLAN 4
E_2950(config)#vtp mode client
Aetting device to VTP CLIENT mode.
E_2950(config)#vtp domain jetcoms
Changing VTP domain name from NULL to jetcoms
E_2950(config)#apply
E_2950(config)#exit
E_2950#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
[OK]
E_2950#
Switch A_2950 Verification
A_2950 Con0 is now available
Press RETURN to get started!
User Access Verification
Password:
A_2950>enable
Enter password: ****
% Incomplete command.
A_2950#ping 172.16.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
A_2950#show running-config
Building configuration...
Current configuration : 866 bytes
!
version 12.1
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname A_2950
!
enable secret 5 $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
!
ip subnet-zero
!
!
spanning-tree extend system-id
!
!
interface FastEthernet0/1
description "Trunking to MainSwitch"
switchport mode trunk
!
interface FastEthernet0/2
switchport mode access
!
interface FastEthernet0/3
switchport mode access
!
interface FastEthernet0/4
switchport mode access
!
interface FastEthernet0/5
switchport access VLAN 2
switchport mode access
!
interface FastEthernet0/6
switchport access VLAN 4
switchport mode access
!
interface FastEthernet0/7
switchport access VLAN 3
switchport mode access
!
interface FastEthernet0/8
switchport mode access
!
interface FastEthernet0/9
switchport mode access
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
switchport mode access
!
interface FastEthernet0/12
switchport mode access
!
interface VLAN1
ip address 172.16.10.3 255.255.255.0
no ip route-cache
!
ip default-gateway 172.16.10.1
ip http server
!
!
line con 0
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
line vty 0 15
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
!
end
A_2950#show VLAN
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12
2 Marketing active Fa0/5
3 Finance active Fa0/7
4 Support active Fa0/6
5 Operation active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
3 enet 100003 1500 - - - - - 0 0
4 enet 100004 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
A_2950#
Switch B_2950 Verification
B_2950 Con0 is now available
Press RETURN to get started!
User Access Verification
Password:
B_2950>enable
Enter password: ****
% Incomplete command.
B_2950#ping 172.16.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
B_2950#show running-config
Building configuration...
Current configuration : 866 bytes
!
version 12.1
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname B_2950
!
enable secret 5 $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
!
ip subnet-zero
!
!
spanning-tree extend system-id
!
!
interface FastEthernet0/1
description "Trunking to MainSwitch"
switchport mode trunk
!
interface FastEthernet0/2
switchport mode access
!
interface FastEthernet0/3
switchport mode access
!
interface FastEthernet0/4
switchport mode access
!
interface FastEthernet0/5
switchport access VLAN 2
switchport mode access
!
interface FastEthernet0/6
switchport access VLAN 5
switchport mode access
!
interface FastEthernet0/7
switchport access VLAN 3
switchport mode access
!
interface FastEthernet0/8
switchport mode access
!
interface FastEthernet0/9
switchport mode access
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
switchport mode access
!
interface FastEthernet0/12
switchport mode access
!
interface VLAN1
ip address 172.16.10.4 255.255.255.0
no ip route-cache
!
ip default-gateway 172.16.10.1
ip http server
!
!
line con 0
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
line vty 0 15
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
!
end
B_2950#show VLAN
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12
2 Marketing active Fa0/5
3 Finance active Fa0/7
4 Support active
5 Operation active Fa0/6
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
3 enet 100003 1500 - - - - - 0 0
4 enet 100004 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
B_2950#
Created by Fery Junaedi
28
Switch C_2950 Verification
C_2950 Con0 is now available
Press RETURN to get started!
User Access Verification
Password:
C_2950>enable
Enter password: ****
% Incomplete command.
C_2950#ping 172.16.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
C_2950#show running-config
Building configuration...
Current configuration : 866 bytes
!
version 12.1
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname C_2950
!
enable secret 5 $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
!
Created by Fery Junaedi
29
ip subnet-zero
!
!
spanning-tree extend system-id
!
!
interface FastEthernet0/1
description "Trunking to MainSwitch"
switchport mode trunk
!
interface FastEthernet0/2
switchport mode access
!
interface FastEthernet0/3
switchport mode access
!
interface FastEthernet0/4
switchport mode access
!
interface FastEthernet0/5
switchport access VLAN 4
switchport mode access
!
interface FastEthernet0/6
switchport access VLAN 2
switchport mode access
!
interface FastEthernet0/7
switchport access VLAN 5
switchport mode access
!
interface FastEthernet0/8
switchport mode access
!
interface FastEthernet0/9
switchport mode access
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
switchport mode access
!
interface FastEthernet0/12
switchport mode access
!
interface VLAN1
ip address 172.16.10.5 255.255.255.0
no ip route-cache
!
ip default-gateway 172.16.10.1
ip http server
!
!
line con 0
password fery
login
line vty 0 15
password fery
login
!
end
C_2950#show VLAN
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12
2 Marketing active Fa0/6
3 Finance active
4 Support active Fa0/5
5 Operation active Fa0/7
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
3 enet 100003 1500 - - - - - 0 0
4 enet 100004 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
C_2950#
Switch D_2950 Verification
D_2950 Con0 is now available
Press RETURN to get started!
User Access Verification
Password:
D_2950>enable
Enter password: ****
% Incomplete command.
D_2950#ping 172.16.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
D_2950#show running-config
Building configuration...
Current configuration : 866 bytes
!
version 12.1
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname D_2950
!
enable secret 5 $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
!
ip subnet-zero
!
!
spanning-tree extend system-id
!
!
interface FastEthernet0/1
description "Trunking to MainSwitch"
switchport mode trunk
!
interface FastEthernet0/2
switchport mode access
!
interface FastEthernet0/3
switchport mode access
!
interface FastEthernet0/4
switchport mode access
!
interface FastEthernet0/5
switchport access VLAN 3
switchport mode access
!
interface FastEthernet0/6
switchport access VLAN 4
switchport mode access
!
interface FastEthernet0/7
switchport access VLAN 2
switchport mode access
!
interface FastEthernet0/8
switchport mode access
!
interface FastEthernet0/9
switchport mode access
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
switchport mode access
!
interface FastEthernet0/12
switchport mode access
!
interface VLAN1
ip address 172.16.10.6 255.255.255.0
no ip route-cache
!
ip default-gateway 172.16.10.1
ip http server
!
!
line con 0
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
line vty 0 15
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
!
end
D_2950#show VLAN
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12
2 Marketing active Fa0/7
3 Finance active Fa0/5
4 Support active Fa0/6
5 Operation active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
3 enet 100003 1500 - - - - - 0 0
4 enet 100004 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
D_2950#
Switch E_2950 Verification
E_2950 Con0 is now available
Press RETURN to get started!
User Access Verification
Password:
Enter password: ****
% Incomplete command.
E_2950#ping 172.16.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
E_2950#show running-config
Building configuration...
Current configuration : 866 bytes
!
version 12.1
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname E_2950
!
enable secret 5 $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
!
ip subnet-zero
!
!
spanning-tree extend system-id
!
!
interface FastEthernet0/1
description "Trunking to MainSwitch"
switchport mode trunk
!
interface FastEthernet0/2
switchport mode access
!
interface FastEthernet0/3
switchport mode access
!
interface FastEthernet0/4
switchport mode access
!
interface FastEthernet0/5
switchport access VLAN 5
switchport mode access
!
interface FastEthernet0/6
switchport access VLAN 3
switchport mode access
!
interface FastEthernet0/7
switchport access VLAN 4
switchport mode access
!
interface FastEthernet0/8
switchport mode access
!
interface FastEthernet0/9
switchport mode access
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
switchport mode access
!
interface FastEthernet0/12
switchport mode access
!
interface VLAN1
ip address 172.16.10.7 255.255.255.0
no ip route-cache
!
ip default-gateway 172.16.10.1
ip http server
!
!
line con 0
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
line vty 0 15
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
!
end
E_2950#show VLAN
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/8, Fa0/9, Fa0/10, Fa0/11
Fa0/12
2 Marketing active
3 Finance active Fa0/6
4 Support active Fa0/7
5 Operation active Fa0/5
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
3 enet 100003 1500 - - - - - 0 0
4 enet 100004 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
E_2950#
Main Switch 2950 Verification
2950-MainSwitch Con0 is now available
Press RETURN to get started!
User Access Verification
Password:
2950-MainSwitch>enable
Enter password: ****
% Incomplete command.
2950-MainSwitch#ping 172.16.10.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.10.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms
2950-MainSwitch#show running-config
Building configuration...
Current configuration : 866 bytes
!
version 12.1
no service single-slot-reload-enable
no service pad
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname 2950-MainSwitch
!
enable secret 5 $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
!
ip subnet-zero
!
!
spanning-tree extend system-id
!
!
interface FastEthernet0/1
description "Trunking to A_2950"
switchport mode trunk
!
interface FastEthernet0/2
description "Trunking to B_2950"
switchport mode trunk
!
interface FastEthernet0/3
description "Trunking to C_2950"
switchport mode trunk
!
interface FastEthernet0/4
switchport mode access
!
interface FastEthernet0/5
switchport mode access
!
interface FastEthernet0/6
description "Trunking to Router"
switchport mode trunk
!
interface FastEthernet0/7
switchport mode access
!
interface FastEthernet0/8
switchport mode access
!
interface FastEthernet0/9
switchport mode access
!
interface FastEthernet0/10
switchport mode access
!
interface FastEthernet0/11
description "Trunking to D_2950"
switchport mode trunk
!
interface FastEthernet0/12
description "Trunking to E_2950"
switchport mode trunk
!
interface VLAN1
ip address 172.16.10.2 255.255.255.0
no ip route-cache
!
ip default-gateway 172.16.10.1
ip http server
!
!
line con 0
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
line vty 0 15
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
!
end
2950-MainSwitch#show VLAN
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4
Fa0/5, Fa0/6, Fa0/7, Fa0/8
Fa0/9, Fa0/10, Fa0/11, Fa0/12
2 Marketing active
3 Finance active
4 Support active
5 Operation active
VLAN Type SAID MTU Parent RingNo BridgeNo Stp BrdgMode Trans1 Trans2
---- ----- ---------- ----- ------ ------ -------- ---- -------- ------ ------
1 enet 100001 1500 - - - - - 0 0
2 enet 100002 1500 - - - - - 0 0
3 enet 100003 1500 - - - - - 0 0
4 enet 100004 1500 - - - - - 0 0
5 enet 100005 1500 - - - - - 0 0
Remote SPAN VLANs
------------------------------------------------------------------------------
Primary Secondary Type Ports
------- --------- ----------------- ------------------------------------------
2950-MainSwitch#
Router VLAN Verification
Route_VLAN Con0 is now available
Press RETURN to get started!
User Access Verification
Password:
Route_VLAN>enable
Password:
% Incomplete command.
Route_VLAN#show running-config
Building configuration...
Current configuration : 625 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
!
hostname Route_VLAN
!
enable secret 5 $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
!
ip subnet-zero
!
!
!
!
!
interface FastEthernet0/0
no ip address
no ip directed-broadcast
!
interface FastEthernet0/0.1
encapsulation dot1Q 1
ip address 172.16.10.1 255.255.255.0
!
interface FastEthernet0/0.2
encapsulation dot1Q 2
ip address 192.168.20.1 255.255.255.0
!
interface FastEthernet0/0.3
encapsulation dot1Q 3
ip address 192.168.30.1 255.255.255.0
!
interface FastEthernet0/0.4
encapsulation dot1Q 4
ip address 192.168.40.1 255.255.255.0
!
interface FastEthernet0/0.5
encapsulation dot1Q 5
ip address 192.168.50.1 255.255.255.0
!
interface Serial0/0
no ip address
no ip directed-broadcast
shutdown
!
interface FastEthernet0/1
no ip address
no ip directed-broadcast
shutdown
!
interface Serial0/1
no ip address
no ip directed-broadcast
shutdown
!
!
ip classless
no ip http server
!
!
!
line con 0
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
line aux 0
line vty 0 4
password $1$u76B$IOFVJ7VxfVXYVpGDrFTcI0
login
!
end
Route_VLAN#
Created by Fery Junaedi
47
Cek Ping dari host A di network Switch 2950
Ke host di network 192.168.30.0
C:\>ping 192.168.30.3
Ke host di network 192.168.40.0
C:\>ping 192.168.40.3
Ke host di network 192.168.50.0
C:\>ping 192.168.50.3
Untuk verifikasi selanjutnya lakukan hal yang sama dengan di atas. Coba cek ping ke setiap host
pada network yang berbeda :
- Network 192.168.20.0
- Network 192.168.30.0
- Network 192.168.40.0
- Network 192.168.50.0
Selamat anda baru saja menjalani langkah demi langkah bagaimana melakukan setting pada
Network VLAN. hanya itu saja. Mudah Bukan ???
: Contoh item 1
: Contoh item 2
| |||